Outside the USA and Canada? You’re in the right place. Call, text or WhatsApp +1 218 530 0202In the USA or Canada? Go to haybuster.com → or call the factory +1 701 252 4601
Tub Grinders / H-1135

H-1135

The flagship. 20 to 25 tonnes an hour. 88 hammers. Remote in your hand.

New for 2027: the H-1135 Contractor
HayBuster H-1135 tub grinder

Watch it work

New for 2027

The fastest tub grinder in Europe.

80 km/h on the road. 25 tonnes an hour in the yard.

The H-1135 Contractor on its road frame The H-1135 Contractor from the rear with the conveyor folded

Contractors in Europe have been telling us for years they want a HayBuster built for the road. Farm to farm, every day, on country roads that are not kind to equipment. So starting in 2027 we are offering the H-1135 Contractor.

Same tub, same mill. Underneath it is a complete road going frame, built with BRIOL, our German partner.

  • DEKRA certified to 80 km/h
  • Air ride suspension
  • PTO shaft with a free running clutch
  • A cradle that locks the conveyor down for the road
  • A screen change that takes about as long as opening the tub

Hook it behind an agro truck or a tractor and go.

Ask about the Contractor →

Pick your chop

The screen decides the chop. Sixteen sizes, and you can run two different ones together.

  • 3mm
  • 5mm
  • 6mm
  • 10mm
  • 13mm
  • 16mm
  • 19mm
  • 25mm
  • 38mm
  • 51mm
  • 76mm
  • 102mm
  • 127mm
  • 152mm
  • 178mm
  • 203mm

Also available: rectangular 89 x 191 mm, 114 x 191 mm, 152 x 191 mm and 229 x 191 mm, and an open screen half.

Pick a hole about twice the chop length you want. Order a few sizes with the machine.

Screen selection guide

Tractor running an H-1135 tub grinder beside a pile of ground material

When the tractor bogs down

Nothing dramatic. That is the point.

  1. A sensor reads the mill speed the whole time you grind.
  2. A heavy or damp bale pulls the RPM down. The governor slows the tub, and stops it if it has to, so the mill can clear.
  3. The RPM comes back and the tub starts turning again on its own.

You keep loading. You don’t touch anything. And with the remote in the loader, you stay out of the dust.

From the Wachendorf display you set tub speed and direction, watch the load and log grinding hours per customer.

Built for the bad bales

Anybody can grind a clean dry bale.

The H-1135 has its mill at the rear of the tub and the biggest mill we put behind a tractor. Damp and heavy material has room to get away. Up to 20% moisture it runs the way the numbers say. Above that it still grinds, and the question becomes how fine you need it. Tell us what you are grinding and we will tell you which screen to run.

Specs

Show full specifications

Machine

Weight6,577 kg
Tub2.72 m inside at the base, 1.27 m deep
Tub tilt90 degrees, for full access to mill, screens and driveline
Loading height2.79 m
Width3.00 m (European machines)

Mill

Hammermill127 cm long, 66 cm diameter, at the rear of the tub
Hammers88 forged swinging hammers, 12.7 mm hardened steel
Hammer rods31.75 mm, case-hardened
Mill grate9-bar, bolt-in. Add or remove bars as conditions change.
Drive8 V-belts, spring tensioned, no manual adjusting

Discharge

AugersTwin, 305 mm
Stacking conveyor7.92 m long, 61 cm wide, rubber belt with cleats
Lift and foldHydraulic

Tractor

Power200 to 315 HP (149 to 235 kW) at the PTO
PTO1,000 rpm, 20-spline or 21-spline shaft
HydraulicsTwo double-acting valves
Electrical12 V
Hydraulic oil on the machine227 litre reservoir. The tank does the cooling, so there is no cooler to clog with dust.

Controls

Radio remoteStandard: tub forward, stop, reverse and speed, conveyor up and down
DisplayWachendorf A35 display with electronic governor

Options

  • PTO shaft, 20-spline or 21-spline
  • Grain hopper for grain grinding
  • Ear corn kit
  • Conveyor discharge guide
  • Screens in any size above

The radio remote and the 9-bar mill grate come with the machine.

Grinding in one place every day? The H-1135 Electric is the same machine on a 300 HP electric motor.

See the H-1135 Electric →

Warranty and parts

Warranty

12 months from the first day you start it. Everything from the hitch to the conveyor is covered. Wear parts like hammers and belts are not.

Parts

In stock in Europe and in the United States. Your dealer orders, we ship.

Parts and service

Questions

What tractor do I need for the H-1135?

200 to 315 HP at the PTO, 1,000 rpm.

How many tonnes per hour?

20 to 25 in dry straw or hay. Finer screens and damp material bring that down.

What chop length can I get?

Screens run from 3 mm to 203 mm. Pick a hole about twice the chop you want.

Which bales fit?

Any bale, round or square, loaded whole.

Can it grind damp straw?

Yes. Up to 20% moisture is normal work. Above that, it depends how fine you need it.

Does it come with a remote?

Yes. The radio remote is standard. You run the tub and the conveyor from the loader.

Can I take it on the road?

The H-1135 Contractor, coming in 2027, is built for it: a full road frame, DEKRA certified to 80 km/h, with air ride suspension.

What stops it plugging when the tractor is overloaded?

The governor slows or stops the tub when mill speed drops and restarts it when the speed comes back.

Can it grind grain?

Is there an electric version?

Yes, the H-1135 Electric. It has its own page.

What is the warranty?

12 months from first start, hitch to conveyor, wear parts excluded.

More answers

Get a quote on the H-1135

← Back

Got it.

We'll come back to you with a machine recommendation and a full quote.

Your details go to our sales team only. No mailing lists, no spam.

Bring your bales. We'll start it up. You do the measuring.

Book a 30-minute call

Built to grind.

Get a quoteWhatsApp
Strohmühle · Molino · Broyeur · Измельчитель · Tub Grinder
Whatever your country calls it, it grinds hay. Since 1966.