Outside the USA and Canada? You’re in the right place. Call, text or WhatsApp +1 218 530 0202In the USA or Canada? Go to haybuster.com → or call the factory +1 701 252 4601
Tub Grinders / H-1030

H-1030

The contractor’s grinder. 15 to 18 tonnes an hour, any bale, any day.

HayBuster H-1030 tub grinder at work

Watch it work

Pick your chop

The screen decides the chop. Sixteen sizes, and you can run two different ones together.

  • 3mm
  • 5mm
  • 6mm
  • 10mm
  • 13mm
  • 16mm
  • 19mm
  • 25mm
  • 38mm
  • 51mm
  • 76mm
  • 102mm
  • 127mm
  • 152mm
  • 178mm
  • 203mm

Also available: rectangular 102 x 152 mm and 127 x 178 mm, and an open screen half.

Pick a hole about twice the chop length you want. Order a few sizes with the machine.

Screen selection guide

When the tractor bogs down

Nothing dramatic. That is the point.

  1. A sensor reads the mill speed the whole time you grind.
  2. A heavy or damp bale pulls the RPM down. The governor slows the tub, and stops it if it has to, so the mill can clear.
  3. The RPM comes back and the tub starts turning again on its own.

You keep loading. You don’t touch anything.

From the Wachendorf display you set tub speed and direction, watch the load and log grinding hours per customer.

Farm or road-ready

Farm

For grinding at home.

  • Farmyard axle
  • 3.00 m wide

Road-ready

For driving farm to farm.

  • Road axle built in Germany
  • Air brakes and parking brake
  • LED road lighting
  • Road hitch
  • TÜV approved
  • 3.00 m wide

In the UK a double axle is available. Ask your dealer.

Built for the bad bales

Anybody can grind a clean dry bale.

The H-1030 has its mill at the rear of the tub, so damp and heavy material has room to get away. Up to 20% moisture it runs the way the numbers say. Above that it still grinds, and the question becomes how fine you need it. Tell us what you are grinding and we will tell you which screen to run.

Specs

H-1030 side view with length, loading height, conveyor length and stacking height 5.89 m 2.79 m 4.74 m 6.4 m H-1030 rear view with width and transport height 3.00 m 3.07 m
Length
5.89 m
Height
3.07 m
Width
3.00 m
Loading height
2.79 m
Conveyor
6.4 m
Stacking height
4.74 m

Dashed line: conveyor folded for transport.

Show full specifications

Machine

Weight6,033 kg
Transport size3.00 m wide, 3.07 m high, 5.89 m long
Loading height2.79 m
Tub3.00 m wide, 2.43 m inside at the base, 1.12 m deep
Tub tilt90 degrees, for full access to mill, screens and driveline

Mill

Hammermill109 cm long, 66 cm diameter, at the rear of the tub
Hammers64 swinging hammers, 12.7 mm hardened steel
Hammer rods31.75 mm, case-hardened
Drive8 V-belts, spring tensioned, no manual adjusting

Discharge

AugersTwin, 305 mm
Stacking conveyor6.4 m long, 61 cm wide, rubber belt with cleats
Stacking height4.74 m
Lift and foldHydraulic, folds over the tub for transport

Tractor

Power150 to 315 HP (112 to 235 kW) at the PTO
PTO1,000 rpm, 20-spline or 21-spline shaft
Hydraulics30 l/min at 103 bar, one double-acting valve
Electrical12 V
Hydraulic oil on the machine227 litre reservoir. The tank does the cooling, so there is no cooler to clog with dust.

Options

The mill grate and geyser plate kit for tough hay and stover comes with the machine.

Warranty and parts

Warranty

12 months from the first day you start it. Everything from the hitch to the conveyor is covered. Wear parts like hammers and belts are not.

Parts

In stock in Europe and in the United States. Your dealer orders, we ship.

Parts and service

Fine chop is measured money

The University of Guelph fed gestating cows the same high-straw ration and changed one thing: the particle size of the straw. The cows on the correctly processed short chop ate 1.43 kg more dry matter a day.

Read the numbers

Questions

What tractor do I need for the H-1030?

150 to 315 HP at the PTO, 1,000 rpm. It runs best from 200 HP.

How many tonnes per hour?

15 to 18 in dry straw or hay. Finer screens and damp material bring that down.

What chop length can I get?

Screens run from 3 mm to 203 mm. Pick a hole about twice the chop you want.

Which bales fit?

Any bale, round or square, loaded whole.

Can it grind damp straw?

Yes. Up to 20% moisture is normal work. Above that, it depends how fine you need it.

Can I take it on the road?

Yes. The road-ready version has a German road axle, air brakes, LED lights and TÜV approval. It is 3.00 m wide.

How high does it stack?

4.74 m, with a 6.4 m conveyor that folds over the tub.

What stops it plugging when the tractor is overloaded?

The governor slows or stops the tub when mill speed drops and restarts it when the speed comes back.

Can it grind grain?

What is the warranty?

12 months from first start, hitch to conveyor, wear parts excluded.

Where do parts come from?

Stock in Europe and in the United States.

More answers

Get a quote on the H-1030

← Back

Got it.

We'll come back to you with a machine recommendation and a full quote.

Your details go to our sales team only. No mailing lists, no spam.

Bring your bales. We'll start it up. You do the measuring.

Book a 30-minute call

Built to grind.

Get a quoteWhatsApp
Strohmühle · Molino · Broyeur · Измельчитель · Tub Grinder
Whatever your country calls it, it grinds hay. Since 1966.